• 32 Bit math
• 32 Bit Floating Point
• Dallas One Wire Support
• If..Then..Else..Elseif..Endif
• Hardware PWM
• Expanded LCD command
• Read and Write Memeory with Basic command
• Basic Interrupts
• Hardware Timers
• Hardware Serial UART Hserin / Hserout
• In Circuit Debugger Now has more features
• New Oscilloscope Software built in
• Free Boot Loader Builder Included
• Free Boot Loader Interface Included

Supported PIC micro MCUs:

PIC12CE673 ,PIC12CE674, PIC12F629, PIC12F675, PIC14000, PIC16C554, PIC16C554A, PIC16C556,PIC16C556A, PIC16C558, PIC16C558A, PIC16C61, PIC16C62, PIC16C620, PIC16C620A, PIC16C621, PIC16C621A, PIC16C622, PIC16C622A, PIC16C62A, PIC16C62B, PIC16C63, PIC16C63A, PIC16C64, PIC16C641, PIC16C642,PIC16C64A, PIC16C65, PIC16C65A, PIC16C65B, PIC16C66, PIC16C661, PIC16C662, PIC16C67, PIC16C70, PIC16C71, PIC16C710, PIC16C711, PIC16C712, PIC16C715, PIC16C716, PIC16C717, PIC16C71A, PIC16C72, PIC16C72A, PIC16C73, PIC16C73A, PIC16C73B, PIC16C74, PIC16C74A, PIC16C74B, PIC16C745, PIC16C76, PIC16C765, PIC16C77, PIC16C770, PIC16C771, PIC16C773, PIC16C774, PIC16C84, PIC16C923, PIC16C924, PIC16CE623, PIC16CE624, PIC16CE625, PIC16F627, PIC16F628, PIC16F83, PIC16F84, PIC16F84A, PIC16F870, PIC16F871, PIC16F872, PIC16F873, PIC16F873A, PIC16F874, PIC16F874A, PIC16F876, PIC16F876A, PIC16F877, PIC16F877A, PIC16F73, PIC16F74, PIC16F76, PIC16F77

Commands in Red are PRO specific.

• ADin - Convert up to 10 analog signals(limited by PICmicro) to digital values (Uses on board A/D converters)
• ASM {....} - Inline assembly
• BRANCH - Computed GOTO (equivalent to ON..GOTO).
• BUTTON - Debounce and auto-repeat input on specified pin.
• CLEAR - Clear all user ram locations, setting all variables to zero.
• COUNT - Count Oscillations on PIN
• DATA - Initialize EEPROM with data
• DEBUG - Displays specified variables to the IDE
• DEBUGIN - Displays specified variables to the IDE
• DISABLE -
• DTMFOUT - Output DTMF signals on PIN.
• DTMFOUT2 - 2 Pin DTMF, Higher quality signal.
• ENABLE -
• ENABLEVIDEO -
• END - Stop execution and enter low power mode.
• EXCEPTION -
• FLOAT - Deals with 32 bit floating point numbers
• FREQOUT - Output frequency on PIN
• FOR..NEXT - Repeat statement(s) specific # of times
• GETCAPTURE -
• GETTMR1 -
• GETWATCHDOG -
• GOSUB...RETURN- Call BASIC subroutine at specified label.
• GOTO - Continue execution at specified label.
• HIGH - Make pin output high.
• HSERIN - Hardware UART, Serial in.
• HSEROUT - Hardware UART, Serial out.
• HSERSTAT -
• HPWM - Hardware Pulse Width Modulation
• I2CIN - Receive Data from I2C device(eeprom)
• I2COUT - Send Data to I2C device (eeprom)
• IF..THEN..ELSEIF..ELSE..ENDIF - Goto if specified condition is true or skip false.
• INPUT - Make pin an input.
• ISRASM {...} - Interrupts
• LCDINIT -
• LCDREAD - Reads RAM on LCD
• LCDWRITE - Send text to an LCD
• LET - Assign result of an expression to a variable.
• LOOKDOWN - Search table for value.
• LOOKUP - Fetch value from table.
• LOW - Make pin output low.
• NAP - Power down processor for short period of time.
• ON BOR -
• ON INTERRUPT - On interrupt jump to.
• ON MOR -
• ONPOR -
• ON RESET - Jump to label after reset.
• OWIN - Dallas One Wire Command
• OWOUT - Dallas One Wire Command
• OUTPUT - Make pin an output.
• PAUSE - Delay (1mSec resolution).
• PAUSEUS - Delay (With in 1us resolution).
• PAUSECLK - Delay based on internal hardware timer.
• PEEK ...POKE - Read / Write specific RAM Location.
• PULSIN - Measure pulse width (10us resolution).
• PULSOUT - Generate pulse (10us resolution).
• PWM - Output pulse width modulated pulse train to pin.
• RANDOM - Generate random value.
• RCTIME - Measure time High to Low on pin. (Reading a Potentiometer)
• READ - Read byte from any on-chip EEPROM.
• READDM - Read strings of data to internal EEPROM
• READPM - Read strings of data from flash program memory
• REPEAT...UNTIL - Repeat a group of commands until expression is true.
• RESETTMR1 -
• RESUME -
• RETURN - See GOSUB command
• REVERSE - Make output pin an input or an input pin an output.
• SERDETECT -
• SERIN - Asynchronous serial input (8N1).
• SEROUT - Asynchronous serial output (8N1).
• SERVO - Control analog Servo motors digitally.
• SET PULLUPS - Set internal pullups.
• SETCAPTURE -
• SETCOMPARE -
• SETEXTINT -
• SETHSERIAL -
• SETHTMR0 -
• SETHTMR1 -
• SETPULLUPS -
• SETTMR0 -
• SETTMR1 -
• SETTMR2 -
• SHIFTIN - Read binary data on PIN w/ Flow control.
• SHIFTOUT - Output binary data on PIN w/ Flow control.
• SLEEP - Power down processor for a period of time.
• SOUND - Generate a specific tone from frequencies 0 to 16000.
• SOUND2 - Same as SOUND but 2 channel 2 Pins.
• SPMOTOR - Control any stepper motor
• STOP - Stop CPU and SLEEP forever
• SWAP - Swap two variable values
• TIMEWATCHDOG -
• TOGGLE - Make pin output and toggle state.
• WHILE...DO - Repeat a group of commands while expression is true.
• WHILE...WEND -
• WRITE - Write byte to any on-chip EEPROM
• WRITEDM - Write strings of data to internal EEPROM
• WRITEPM - Write strings of data to flash program memory
• XIN - X-10 input
• XOUT - X-10 output

PRO only macros and inline assembly commands:

• @BANK
• @CALL
• @GOTO
• @HIGH
• @INPUT
• @LOW
• @MSDELAY
• @OUTPUT
• @RATEDELAY
• @RETURN
• @TBLJMP
• @USDELAY
• ADDCF
• ADDDCF
• ADDLW
• ADDWF
• ANDLW
• ANDWF
• ASM{}
• B
• BC
• BCF
• BDC
• BNC
• BNDC
• BNZ
• BSF
• BTFSC
• BTFSS
• BZ
• CLRC
• CLRDC
• CLRF
• CLRW
• CLRWDT
• CLRZ
• COMF
• DECF
• DECFSZ
• INCF
• INCFSZ
• IORLW
• IORWF
• LCALL
• LGOTO
• MOVF
• MOVFW
• MOVLW
• MOVWF
• NEGF
• NOP
• OPTION
• RETFIE
• RETLW
• RLF
• RRF
• SETC
• SETDC
• SKPC
• SKPDC
• SKPNC
• SKPNDC
• SKPNZ
• SKPZ
• SLEEP
• SUBCF
• SUBDCF
• SUBLW
• SUBWF
• SWAPF
• TRIS
• TSTF
• XORLW
• XORWF

Math commands (Floating point commands are PRO only)

• NOT, ABS, SIN, COS, - (NEG), DCD, NCD, SQR, Random,
  FNEG, INT, FLOAT, BIN2BCD, BCD2BIN, ~(NOT), !(NOT)
• <, <=, =, >=, >, <>
• And, Or, Xor
• Rev, Dig
• <<, >>
• MAX, MIN
• &, |, ^, &/, |/, ^/
• *, **, */, /, //, FMUL, FDIV
• +, -, FADD, FSUB